Plumbing 101: A Necessity for Bathtub Installation
Plumbing 101: A Necessity for Bathtub Installation
Blog Article
Just how do you really feel on the subject of A Step-by-Step Guide to Installing a Bathtub?
Mounting a bath tub isn't specifically rocket science, but it does call for solid plumbing, carpentry, and sometimes, tiling skills. Replacing an old tub with a brand-new one is likewise a reasonably difficult project. If the old tub is conveniently accessible, the project can relocate quickly; if you have to open up a wall to get rid of the old tub as well as position the brand-new bathtub, the task is much harder. In either situation, the job is within a home handyman's abilities, although you will require a helper to move out the old tub and also set in the new one. See to it you have qualified yourself for the work and are comfortable attempting it. Rather than working with a service provider to take control of a halfway-completed project, it is much better to consider utilizing one prior to you start. Chances are you may require an expert plumber to make tube connections.
This short article will help you install a brand-new bathtub in your restroom if you have currently bought a brand-new tub and don't need to alter the setup of your previous supply of water pipes.
Your tools as well as material checklist must consist of the following:
Getting ready for the Installment
First of all, the sustaining structure supplied with the bath ought to be fitted (if called for) according to the producer's instructions. Next off, fit the taps or mixer to the tub. When fitting the faucet block, it is necessary to make certain that if the tap comes with a plastic washer, it is fitted in between the bath and also the taps. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the faucets system to stop pressure on the bath tub.
Fit the flexible tap connectors to the bottom of both faucets using 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet via the hole in the bath. Use the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. See to it you make use of all of the supplied washing machines.
Attach the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom should now be ready to be suited its last position.
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your installment, after that the first thing you ought to do is disconnect the water. After doing so, switch on the faucets to drain any water staying in the system. The process of eliminating the existing faucets can be rather bothersome because of the limited access that is typically the instance.
Use a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipelines to the taps. Have a towel prepared for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipes have actually been eliminated, utilize the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the single taps from turning during this procedure. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any old securing compound.
Before going on to fit the brand-new taps, compare the pipeline links on the old taps to the brand-new faucets. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Setting up the Tub
Making use of both wood boards under its feet, put the bathtub in the called for placement. The wooden boards are useful in uniformly spreading out the weight of the bath tub over the area of the boards instead of focusing all the weight onto 4 tiny points.
The next objective is to ensure that the bathtub is leveled all round. This can be achieved by inspecting the spirit level and also adjusting the feet on the tub till the level checks out level.
To install taps, fit all-time low of the outermost adaptable faucet port to the suitable supply pipe by making a compression sign up with; after that do the same for the other tap.
Activate the supply of water and also inspect all joints and new pipework for leakages and tighten them if essential. Load the bathtub as well as also check the overflow outlet and also the typical outlet for leaks.
Lastly, repair the bathroom paneling as explained in the manufacturer's user's manual. Tiling and securing around the tub should wait till the bath tub has been made use of a minimum of once as this will settle it right into its last position.
Suitable New Taps
If the tails of the new faucets are plastic, then you will certainly need a plastic port to stop damages to the thread. One end of the connector fits on the plastic tail of the tap as well as the other end gives a link to the current supply pipes.
If you need to fit a monobloc, after that you will call for lowering couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next off, position the faucet in the mounting opening in the bath/basin guaranteeing that the washing machines are in location in between the tap and the sink. Secure the tap in place with the producer given backnut. As soon as the faucet is safely in place, the supply pipes can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular faucet ports. The former kind must be linked to the faucet finishes first, tightening only by hand. The supply pipelines can later on be connected to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the area where the bath meets the tile, it is necessary to secure the joins with a silicone rubber caulking. This is necessary as the installation can relocate enough to break an inflexible seal, causing the water to pass through the wall surface between the bathroom as well as the tiling, resulting in complications with moisture as well as possible leaks to the ceiling below.
You can choose from a selection of coloured sealers to assimilate your fixtures and fittings. They are sold in tubes and cartridges, and also can sealing spaces up to a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to constantly load the tub with water prior to securing, to allow for the movement experienced when the tub remains in usage. The sealant can fracture relatively early if you do not consider this movement before securing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally conveniently readily available on the market. It is advisable to fit the ceramic tiles using water-resistant or waterproof sticky and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I stumbled upon that blog entry on A Step-by-Step Guide to Installing a Bathtub when doing a search on the web. Sharing is caring. You just don't know, you might be doing someone a favor. We enjoy reading our article about How to Install a Bathtub Yourself.
Source This Article Report this page